Try to make it look straight and nice, if you can. Now continue piping your line beyond the valve that you have just installed and head towards the pump. You made some great suggestions. Unless you are planning on having a fast wading competition. You definitely keep the main drain open if you want its benefits.
Leave a Reply Cancel reply Your email address will not be published. These openings are where the pump and filter hook up to the pool and they are both located high up and right next to each other. Most above ground swimming pool systems like Hayward pool products will use a union between the pump and the filter as you can see in the above picture. Though, it can be done fairly easily if you know how.
How to Hook Up a Swimming Pool Filter
After blowing the line out for the winter, my above ground pool started losing water. For those who owe a backyard swimming pool, pool maintenance is their primary concern. They came with them to keep the cost down and who cared anyway. It does take more than a screwdriver and duct tape to install one, so unless you have some plumbing knowledge, you do-it-yourselfers should maybe leave installing one to the pool installer.
Yeah, you want to make sure you glue everything properly. When I went to tighten down the ring one of the screws would not hold tight and the ring broke. When you can see the screw holes, take the main drain ring and gasket and carefully screw the ring down onto the main drain. You are almost done, sites but this is the hardest plumbing part. Place the main drain with its attached pipe in place.
And, it should be as having a leaking pool really sucks. Jack again, do you have a preferred brand or type of drain box to use? Make sure to tighten all hose clamps on the inlet and the outlet of the swimming pool Chlorine feeder as well. Connect the line to the pump and skimmer You are almost done, reviews but this is the hardest plumbing part.
Main Drains in Above Ground Pools
Another thing you can do to keep the leaves, insects and other debris out of your pool, is you can go and purchase a pool cover. So does that mean I should keep both ball values open when in normal filter mode? Make sure you are not leaking after that valve.
Once all the piping in the trench is set and glued, go ahead and bury it. Now we did call someone and they told us our hoses were on backward so we fixed that but it is still running water out what do we do? Now with my poo draining into the ground, I am left with pulling the liner off of half of the pool to replace the bottom drain. Any suggestions on this concern?
Congratulations, you did it! There is some weird human psychology that makes people think that. If you get tired of dealing with all that mess, you can instead set up your vac hose like you are vacuuming and just leave it in the pool with the vac head at the bottom.
Main Drains (They re Not Just for In-grounds)
- Cutting for the main drain is really easy.
- The duct tape is to keep dirt out of the screw holes during installation.
- Or, should I keep the ball value from the main drain closed, and only have the skimmer open?
- Dig the trench Measure in from the pool track or wall in three different places to determine the center of the pool.
- Now that the season is over the water is very cold.
The one thing that you need to know is the the Chlorinator has to be hooked up with the direction of flow in mind. We bought our house in the fall and had a company come winterize it. We have Hayward drains but how do you determine if they are working? Screw directly through the liner. Would getting a new seal and drain cover fix this or should I take the drain out?
Mark the center and dig a trench toward the right side of where the pool skimmer is. There is no water currently attached to the pool the filter and pump are not hooked up as well. Now, just about all the middle-of-the-road and higher end above grounds will have more than big enough pumps and filters and they are built to last many years. You will now want to get another pool hose just like the one that you used to hook up the pool pump to the skimmer and also put hose clamps on each end of this pool hose.
Connecting the pool return
There are three ways an above ground pool can get better circulation. This is our first year with an above ground pool we set the Hayward pump up and when we turn it on to filter the water comesnout of the waste. As stated above, installing a main drain in an above ground pool on your own may not be the best idea as it takes some doing.
And, they are great for keeping the pool cleaner and for much better circulation. My preference is to open it from the outside and then connect the hose to drain the water properly. Same goes for any foam product you use for the floor. Make sure to also tighten these hose clamps.
- You may be able to keep the main drain line closed until the weather warms by only using the skimmer intake line for the open spring season.
- How does that pool water get through the pump and filter?
- So, my guess is that this was only installed for the hydrostatic releif valve capability, and not as a functioning main drain going back to the filter there is also no diverter valve to do so.
Let the pool fill at least a few inches or more. Any Ideas on how to fix this with out draining pool? The theory is that the drains are to far apart for on person to block so the suction would just redirect to the unblocked drain.
Maybe you have a train that goes through your yard? Doing this will completely cover the inside of the drain and its screw holes. Additional mention, we were planning to get one of those pool robots to clean the pool, if that makes a difference at all. First off, how can the screws be getting loose? The only thing that has stopped the loss of water was to close off the drains.
There is no suction or pressure of any kind. Dan, what is the reason for not running the piping under the straps? Prepare the main drain Silicone in the bottom threaded plug and silicone the threaded male to slip fitting and glue a full piece of pipe to it.
How to Hook Up an Above Ground Pool Vacuum
So the water pressure built up and apparently one of the ball valves blew apart, pieces halfway across the yard. So if you have a union like the one that is pictured above you will want to tighten the union nut with a large pair of water pump pliers. You mention that a main drain will help keep the pool cleaner and provide better circulation. Many years back, above grounds only came with really crappy canister sand filters and undersized pumps.
How To Hook Up An Above Ground Pool Filter System
How To Hook Up An Above Ground Pool Filter System
Do the top of the drains need to be recessed below the level of the pool edge in order to work correctly? It will not but you have the cut a hole in the liner pad around the drain before you install the liner. Silicone in the bottom threaded plug and silicone the threaded male to slip fitting and glue a full piece of pipe to it. In order to connect the skimmer to the pump you will need to take one of the pool hose and put a hose clamp on each end.
It may be hard to find the plug for purchase though. Never in when the pool is in use. Many above ground pools have in line pool chlorine feeders like the one pictured above. You can look it up though.
Also, the dual drain is to prevent entrapment by suction. Some times auto cleaners will get caught on main drains so that may be an issue. You will want to take one end of the pool hose and connect it to the return fitting on the pool wall. Installing a Main Drain As stated above, installing a main drain in an above ground pool on your own may not be the best idea as it takes some doing. You will need to take one end of your hose and connect it to the bottom of the skimmer that is on the pool wall.